·    Samsung S10 Not charging solution iC chip, Dead solution iC S5200AReplace or repairing procedure of S5200A Power iC

Here's a step-by-step procedure for replacing or repairing the S5200 power ic in samsung s10 or similar smartphone:

Tools and Materials Needed:

High-intensity heat insulation tape

Board holder or board catcher

Flux paste (good quality)

Soldering wick

Soldering flux

Original replacement S5200 power ic in samsung s10

Heat gun or heat station (adjustable temperature)

Procedure:

Diagnosis:

Ensure that the issue with your smartphone is indeed related to the S5200 power ic in samsung s10. Symptoms typically include network connectivity issues, poor signal reception, or problems with mobile data.

Preparation:

Cover the entire motherboard with high-intensity heat insulation tape to protect surrounding components from heat damage during the soldering process. Secure the motherboard in a board holder or board catcher to maintain stability.

Apply Flux:

Apply a good quality flux paste evenly around the S5200 power ic in samsung s10 that needs to be removed. Flux helps in solder flow and reduces oxidation during the soldering process.

Heat Application:

Use a heat gun or heat station to apply heat to the IC. Ensure the temperature does not exceed 350 degrees Celsius (662 degrees Fahrenheit). Heat gradually and evenly around the IC to avoid overheating.

IC Removal:

As the flux melts and the solder loosens, gently nudge the IC with tweezers or a pry tool. The IC should start to move or lift from its original position. Be patient and avoid excessive force to prevent damage to the motherboard.

Cleaning:

Once the IC is removed, clean the motherboard's IC pads using soldering wick to remove excess solder and old flux. Apply soldering flux to ensure clean and fresh solder joints for the new IC.

Prepare for Replacement:

Apply a small amount of flux to the cleaned IC pads on the motherboard.

Install New IC:

Carefully place the original replacement S5200 power ic onto the prepared pads on the motherboard. Ensure proper alignment and orientation of the IC.

Heat Application for Soldering:

Use the heat gun or heat station again to solder the new IC onto the motherboard. Heat should be applied at a temperature between 300 to 350 degrees Celsius (572 to 662 degrees Fahrenheit) depending on your equipment.

Heating Time:

Heat the IC for approximately 1 to 1.5 minutes, ensuring that the solder melts evenly and forms good connections between the IC and the motherboard pads.

Cool Down:

Allow the motherboard to cool naturally for about 3 to 5 minutes after soldering. This helps in stabilizing the solder joints and preventing thermal shock to the IC and surrounding components.

Final Checks:

Inspect the solder joints under magnification to ensure they are smooth, shiny, and free of bridges or cold joints. Any excess flux residue should be cleaned using isopropyl alcohol and a brush or cotton swab.

Reassembly and Testing:

Once satisfied with the soldering job, reassemble the smartphone carefully. Power on the device and test to ensure the issue with the S5200 power ic  has been resolved. Check for proper network connectivity and signal reception.

Conclusion:

Following this detailed procedure with care and precision is essential for successfully replacing or repairing the S5200 power ic in samsung s10 or similar smartphone. Remember to work in a static-safe environment and exercise caution to avoid damaging other components on the motherboard. If you're unsure or inexperienced with microelectronics, seeking assistance from a professional repair technician is advisable.

You may also need following chip ic

CHARGING POWER IC BACK LIGHT DISPLAY LIGHT AND COIL IC ANDROID DIODE IC CPU PROCESSOR IC Emmc & RAM CHIP Intermediate Frequency Integrated Circuit (IF IC) POWER AMPLIFIER SIGNAL SUPPLY PA CHIP IC POWER SUPPLY MANAGEMENT IC FINGERPRINT SENSOR IC Touch Screen Sensor IC WIFI BLUE TOOTH IC  Touch Screen Sensor IC
Delivery Time:

Standard Shipping (Post): 1-2 days

Tcs:1-2days

MnP:1-2days

Leoperd:1-3days

Package : All items are brand-new, tested and protected during shipping by being individually sealed in plastic bags and cushioned by bubble wrap within a sturdy box.

Please be cautious when opening your package, as some items may be small and easily overlooked or misplaced.

1.     Brand-new

2.     Fully compatible integrated circuit (IC).

3.     Thoroughly tested for quality assurance.

4.     Custom-made for specific mobile phone models, ensuring precise fit.

5.     Ideal replacement for damaged or faulty ICs in your device.

6.     Made from premium materials for long-lasting durability.

7.     Note: Product appearance may differ from the image provided.

Notice:  If you encounter any problems with the item you receive, whether it's defective or incorrect, don't hesitate to reach out to us. We're committed to resolving the issue and ensuring your satisfaction. Additionally, if you experience any difficulties while using the item, we're happy to provide support and assistance to help you make the most of it.

Contact us:  For any inquiries, you can reach us through email or whatsapp : https://wa.me/message/RGYHJUTERPVWH1.. Please do not be concerned if you don't receive an immediate response during off-hours. Upon receiving your email, we will attend to it and respond promptly. 

Feedback: We would be very grateful if you could take the time to leave a positive review and rate our service 5 stars. If you encounter any issues, don't hesitate to reach out to us before leaving a negative review. Our team is committed to addressing any concerns promptly and effectively.